你好,欢迎光临济南兰鑫厨房排烟!

产品中心

油烟净化的清洗要注意哪些流程?

来源:/添加时间:2018-04-25 15:31:12
第一步:关闭电源泄放电荷
Step 1: turn off the power and discharge the charge
安全是最为重要的,对于接触所有用电器我们都要关闭其电源,放掉其中的电荷。不要觉得关闭电源就安全了。这个是错误的认知。打开设备检测们过后,手握住螺丝刀的绝缘手柄,用螺丝刀的金属部分短接一下电场其中一个筒的阴阳极。这样就能放电荷了。
Safety is the most important. To contact all electrical appliances, we must turn off the power and release the charge. Don't feel safe to turn off the power. This is a mistaken cognition. After opening the equipment test, hold the insulated handle of the screwdriver, and use the metal part of the screwdriver to pick up the cathode and anode of the electric field. So the charge can be put on.
第二步:拧下螺栓,抽拉出电场
Second step: screw down the bolt and pull out the electric field
确保电源已经断开的情况下,拧下固定用的螺栓,打开维护门,再用手抽拉电场两侧,在电场即将抽出时,末端用手扶住,防止突然脱落,使电场受损。(注意电场要轻拿轻放,不能挤压,重摔)
To ensure that the power has been disconnected, the fixed bolt is unscrewed, the maintenance door is opened, and the hand draws the two sides of the electric field. When the electric field is about to be pulled out, the end is supported by hand to prevent the sudden drop off and the electric field is damaged. (notice that the electric field should be light and light, not extruded and heavy).
第三步:拆卸配件,方便清洗
Third step: remove parts, convenient for cleaning
因为绝缘子湿水极易造成漏电,故要把绝缘子拆下,同时分开阴极针和阳极圆筒方便进一步清洗。
济南厨房排烟管道
Because the wet water of the insulator is very easy to cause electricity leakage, it is necessary to remove the insulators and separate the cathode pin and the anode cylinder for further cleaning.
第四步:电场清洗,浸泡冲洗
Fourth steps: electric field cleaning, soaking and washing
用一个不锈钢或塑料清洗槽容器,外形大于电场外形尺寸就可。避免清洗时弄脏地板,故将油烟净化器包裹起来,然后在容器中拆掉包裹袋。用重量比为1:20的烧碱与热水混合溶液泡洗,根据油污的程度不同浸泡的时间长度也不同,浸泡好然后用高压水枪加清水冲洗,放置在干净的地方晾干。
Use a stainless steel or plastic cleaning tank container, the shape is larger than the electric field size. To avoid fouling the floor when cleaning, wrap the fume cleaner and remove the package bag in the container. Soak with a mixture of caustic soda and hot water at 1:20. The length of the soaking time is different according to the degree of oil pollution. Soak well then rinse with water gun and water with water, and dry it in a clean place.
第五步:绝缘子的检查与清洗
Fifth step: the inspection and cleaning of insulators
检查发现绝缘子如有烧坏的痕迹如有裂缝,则要更换掉;需把绝缘子和绝缘瓷上边的油污清洁干净,并保持干燥。清洗方法如下:应先在绝缘子上喷酒精,然后用干抹布擦干。
The examination found that if the insulator had burnt marks, if there were cracks, it was necessary to replace them. It is necessary to clean the oil stains on insulator and insulation porcelain and keep them dry. The cleaning methods are as follows: first, spray the alcohol on the insulator, then dry it with a dry cloth.
第六步:装配检查校正
Sixth step: assembly check correction
把清洗干净的部件以此装配,对于电场应该按照原位置装入,电场的方向不能呢个颠倒。
To assemble the cleaned parts, the electric field should be loaded in the original position, and the direction of the electric field can not be reversed.
第七步:设备调试
Seventh step: equipment debugging
清洗结束,装配结束过后就应该进行调试,如果调试没问题则没问题了,如果调试出现电源指示灯闪烁时,并伴随着有“兹兹”的响声,则需取出对应电场,如果实在装配不好,无法解决那只有和厂家联系装配了。
After the end of the cleaning, it should be debugged after the end of the assembly. If there is no problem to debug, if the debug power indicator flashes and the sound of "Z" is accompanied by the sound of "Z", the corresponding electric field should be taken out. If it is not well assembled, it can not be solved only with the manufacturer.

上一篇:离心风机跟轴流风机在启动时要注意哪些?
下一篇:通风管道的安装工程需要注意哪些?

济南兰鑫厨房排烟    电话:15610162918    天天彩票网jamubiohsa.com版权所有
本网站由济南诺商提供技术支持      网站地图 XML

本站图片均由网站所有方提供,部分图片来源于网络,如有任何疑问请第一时间与我们联系,未经沟通本站不承担相关法律责任!

免责声明: 本站资料及图片来源互联网文章,本网不承担任何由内容信息所引起的争议和法律责任。所有作品版权归原创作者所有,与本站立场无关,如用户分享不慎侵犯了您的权益,请联系我们告知,我们将做删除处理!